中国空间科学技术

›› 2011, Vol. 31 ›› Issue (1): 62-69.doi: 10.3780/j.issn.1000-758X.2011.01.009

• 技术交流 • 上一篇    下一篇

星载辐射计扫描镜太阳辐射热-结构建模与仿真

游思梁1, 陈桂林2,  王淦泉2   

  1. (1 上海交通大学航空航天学院,上海 200240)(2 中国科学院上海技术物理研究所,上海 200083)
  • 收稿日期:2010-03-26 修回日期:2010-08-08 出版日期:2011-02-25 发布日期:2011-02-25
  • 通讯作者: 游思梁 通信地址：上海市宝山区共富四村42号301室 邮编：201906 E-mail:afflatus99@yahoo.com.cn
  • 作者简介:游思梁 1980年生，2008年获中国科学院上海技术物理研究所电路与系统专业博士学位，现为上海交通大学航空航天学院博士后。研究方向为航空航天飞行器综合环境控制技术。

Thermal-structural Modeling and Simulation for Scan Mirror on Imager in Solar Radiation

YOU  Si-Liang1, CHEN  Gui-Lin2, WANG  Gan-Quan2   

  1. (1 School of Aeronautics and Astronautics, Shanghai Jiaotong University, Shanghai 200240)(2 Shanghai Institute of Technical Physics,Chinese Academy of Sciences, Shanghai 200083)
  • Received:2010-03-26 Revised:2010-08-08 Published:2011-02-25 Online:2011-02-25

PDF (PC)

2486

被引次数

8

摘要： 三轴稳定卫星平台搭载的光学有效载荷都存在午夜太阳辐射干扰问题，由此产生的热变形效应对光学系统的成像品质影响显著。采用复杂外热流近似建模技术，以及多软件耦合有限元仿真方法，以FY-4卫星的扫描辐射计为应用背景，研究了昼夜太阳辐射对星载辐射计扫描镜产生的热效应，并对不同热设计条件下的工况进行了对比分析。分析结果显示：扫描镜侧面及背面的热控涂层选取对其热变形有重要影响，但是仅仅通过热设计解决温度波动和热变形的矛盾是不够的，需要通过改进扫描镜的材料和优化光机结构加以改善。

关键词: 扫描镜, 太阳辐射, 热效应, 三轴稳定平台, 卫星

Abstract: The solar-radiation disturbance exists in the optical payloads onboard the three-axis stabilized satellite platform. It leads to thermal distortion, which obviously affects the imaging quality of optical system. The approximate modeling technique of complex external heat flux was applied, as well as the multi-software-coupled finite element simulation. The thermal effect of the imager′s scan mirror caused by solar radiation was researched, and compared under different thermal design conditions on the FY-4 imager. The optimal scheme of the thermal design of the scan mirror was obtained. The result shows that the thermal distortion is closely related to the thermal coating on the side and the back of the scan mirror. It is difficult to  resolve  the conflict  between the temperature fluctuation and the thermal distortion if only using the thermal design method. It is necessary to improve the material of the scan mirror or adjust the optical-mechanical structure.

Key words: Scan mirror, Solar radiation, Thermal effect, Three-axis stabilized platform, Satellite