中国空间科学技术

中国空间科学技术 ›› 2014, Vol. 34 ›› Issue (6): 65-.doi: 10.3780/j.issn.1000-758X.2014.06.009

• 技术交流 • 上一篇    下一篇

适用于月面高温环境的嫦娥三号地形地貌相机热设计

 宋馨1, 张有为1, 周向东2, 刘自军1   

  1. (1 北京空间飞行器总体设计部,北京 100094)(2 中国科学院光电技术研究所,成都 610209)
  • 收稿日期:2014-03-06 修回日期:2014-06-25 出版日期:2014-12-25 发布日期:2014-12-25
  • 作者简介:宋暋馨 1986年生,2010年获北京航空航天大学人机与环境工程专业硕士学位,工程师。研究方向为航天器热控设计。

Thermal Control Design for Topography Camera of Chang'e-3 Under High Temperature Environment o fLunar Surface

 SONG  Xin1, ZHANG  You-Wei1, ZHOU  Xiang-Dong2, LIU  Zi-Jun1   

  1. (1 Beijing Institute of Spacecraft System Engineering,Beijing 100094)(2 The Institute of Optics and Electronics,The Chinese Academy of Sciences,Chengdu6 10209)
  • Received:2014-03-06 Revised:2014-06-25 Published:2014-12-25 Online:2014-12-25

PDF (PC)

1738

被引次数

2

摘要： “嫦娥三号暠月面探测器上安装的地形地貌相机工作时直接暴露在月面高温环境下,受月表红外辐射影响很大,给热控设计带来很大难题。为解决设备工作时的高温问题,在外热流分析的基础上提出了以“最佳散热位置暠为核心的热控方案,设备处于“最佳散热位置暠时能够获得较好的初始温度和最快的降温速率;另外通过把散热面布置在月表红外辐射热流最小的位置并在除散热面以外的其他表面包覆多层隔热组件这两个措施,可以最大程度减小月表红外辐射的影响。地形地貌相机在轨开机工作前的各飞行阶段遥测数据均满足存储温度指标要求并且有较大余量;开机工作环拍一周的遥测数据满足工作温度指标要求并且与热分析结果符合较好,初始温度与遥测温度数据偏差为-1灡7曟,温升速率和降温速率偏差分别为14灡9%和16灡9%。这表明该热控方案正确可行,可为后续中国深空探测类似热控问题参考。

关键词: 热控设计, 月面环境, 散热面, 地形地貌相机, 月面探测器, 嫦娥三号

Abstract: Topography camera of Chang'e-3 probe is installed directly exposed to the high temperature environment of the lunar surface.The high temperature environment is great challenge to the thermal control design. To solve the high temperature problem,the best radiation position was presented as the core  of thermal design based on the heat flow analysis.The topography camera could obtain suitable initial temperature and fastest cooling rate when it was located at the best position.Meanwhile,the infrared radiation of the lunar surface was reduced as much as possible by arranging the radiator position appropriately and wrapping the camera with multilayer insulation.The telemetrydata of the topography camera meet the requirements of the storage stage temperature and have a large margin.Considering one-circle photograph,the topography camera temperature meets the operating temperature requirements,and the results are in good agreement with the thermal analysis.The thermal control design for the topography camera is proved to be correct and can be referred by the devices with similar problems of the deep space exploration field.

Key words: Thermal control design, Lunar environment, Radiator, Topography camera, Lunar surface probe, Chang'e-3